Premium

Standardized requirements for the quality of PV modules, solar cells and wafers are given in the according IEC norms (e.g., IEC 61215, 61646, and IEC 61730 for modules). However, the manufacturers of cells purchasing wafers and the module manufacturers purchasing cells want information beyond the final check of the product and to monitor each step during the production process to identify harsh handling and/or machine faults at the earliest stage possible. With consequential improvements of the process enabled, continuous improvements in throughput and yield improvement of the factory are likely, also allowing an early feedback on quality issues to the raw material supplier. Furthermore, by knowing all characteristics and factors of the cell and the module, prediction of electrical energy yield during the life cycle of a PV power plant is becoming more accurate and more reliable.

The importance of rapid and accurate measurement of the electrical power output and related characteristics of photovoltaic (PV) modules or panels concluding the manufacturing process cannot be overemphasized. Even though these modules will likely be deployed under a variety of outdoor solar illumination conditions, they must be tested under a set of standard conditions to assure consistency of results demanded by both the manufacturer and the customer. The ability to provide a measurement tool for this critical manufacturing step that possesses the proper specifications and qualities, ranging from spectral accuracy to ease-of-use, is imperative.

The first edition of the Photovoltaics International journal, published in August 2008, was created in response to what was deemed to be a growing need for an unbiased technical publication for the solar cell and module manufacturing industry. With this in mind, the first edition of Photovoltaics International saw the commissioning of papers from a wide range of sectors, such as NREL’s overview of the CPV sector, IMEC’s thin-film efficiency gains via plasma texturing, site selection with IBM PLI, Q-Cells on silicon nitride thin films and Navigant Consulting’s market overview.

Increasing the efficiency and yield of production line processes forms an integral part of PV manufacturers’ technology roadmaps. For their next generation production lines, non-contact processing equipment is considered essential. This prioritizes laser-based processing, already established at several steps in c-Si and Thin-Film cell manufacturing. This paper summarizes the key issues when using lasers within PV production lines.

Design and performance qualification testing of PV modules consists of a set of well-defined accelerated stress tests with strict pass/fail criteria. ASU-PTL is an ISO 17025-accredited testing laboratory and has been providing photovoltaic testing services since 1992. This paper presents a failure analysis on the design qualification testing of both crystalline silicon (c-Si) and thin-film technologies for two consecutive periods: 1997-2005 and 2005-2007. In the first period, the industry was growing at a slower rate with traditional manufacturers, with qualification testing of c-Si technologies being primarily conducted per Edition 1 of the IEC 61215 standard. In the second period, the industry was growing at an explosive rate with new manufacturers joining the traditional manufacturers, while qualification testing of c-Si was primarily conducted per Edition 2 of IEC 61215. Similar failure analysis according to IEC 61646 has also been carried out for thin-film technologies. The failure analysis of the test results presented in this paper indicates a large increase in the failure rates for both c-Si and thin-film technologies during the period of 2005-2007.

Each year, the photovoltaic market grows at a two-digit growth rate. However, the resulting economy-of-scale effects are not enough to achieve grid parity on their own. In order to reduce the production costs to grid parity level, new concepts and ideas must be realised as the basis for a photovoltaic factory. There are four main requirements that must be fulfilled in order to adhere to this cost reduction strategy: a highly integrated factory; automated and stable processes; a production control system (PCS) that provides the statistic data in order to continually optimise the processes; and an optimally-sized aligned production capacity.

The rapidly-growing photovoltaic market has placed a strong demand on manufacturers to decrease solar cell production costs. For thin-film solar cells, this can be achieved by increasing substrate sizes to achieve a better productivity and by adding more advanced layer stack systems to enhance the solar cell’s efficiency. Nearly all required layers of the prominent thin-film-based solar cell types (a-Si/µc-Si, CdTe and CI(G)S) can be deposited by using plasma processes. On the one hand, plasma-enhanced chemical vapor deposition (PECVD) is used for the deposition of a-Si and µc-Si layers. On the other hand, magnetron sputtering is used for coating with transparent conductive oxides as ITO (indium tin oxide) and ZAO (aluminium-doped zinc oxide), metallic back contact layers such as Ti, Al and Mo, or components of the compound semiconductor layers such as Cu and In. Magnetron sputter processes use direct current (DC) or pulsed DC, whereas radio frequency (RF) power is used for PECVD processes. Of utmost importance to get a reliable, high-efficiency solar cell is a good uniformity of the deposited layers and the need for the layer to be defect-free. Defects such as particles and splashes are created inside the plasma when an unwanted local discharge - a so-called arc - occurs. This arc can be eliminated by switching off the power supply. The faster this is done, and the less energy that is delivered into the arc, the smaller and more insignificant the defect creation will be. For this reason, as well as for precise control of electrical power, advanced, fast-reacting arc management is very important to attain high-quality solar cell coatings.

Thin-film solar cell manufacturing is poised to make a giant leap in scale with the birth of the gigawatt fab. Commercial thin-film plants are typically sized based on the capacity of the production line from the chosen equipment supplier. In most cases, initial investments have been for a single line, typically with an output capacity of no more than 60MWp. This period of initial development has allowed the industry to prove the robustness of the technology and capabilities of the equipment, as well as to understand the significance for the cost-per-watt of key cost drivers such as materials reduction, cell efficiency increases, and productivity. While large-scale manufacturing will positively impact costs, it presents a unique set of challenges for equipment and material suppliers, as well as the engineering and contracting companies tasked with designing, building, equipping and running a facility on this scale. In this paper, we present the insights of two specialty companies in the solar industry. Turner and Townsend, a design and project management consultancy, and Linde, glass manufacturer and gas and chemical company - share their views of the challenges of the gigawatt fab in three dedicated sections.

The deposition of thin films is a key technology for a large variety of technical and scientific applications. Among them is the deposition of silicon nitride (SiNx) to passivate the surface of silicon solar cells. The SiN film serves several purposes. It is a broadband anti-reflection layer, it serves to saturate dangling bonds and/or other surface states of the silicon, and last but not least, it is a protection layer to prevent alkali ions and other impurities from diffusing into the silicon causing perturbations of the performance of the solar cell. This multitude of properties to be fulfilled at the same time often causes difficulties in assessing the effect of a single process parameter, let alone the task of optimizing the SiN film in all required aspects at the same time. The aforementioned technical features of the SiN film provide the very property that largely determines the aesthetically pleasing appearance of a cell, and hence a PV module, as the colour of the module is determined by the cell composition. In order to complicate things further, there are numerous deposition techniques being applied both on a scientific level as well as in production environments.

Thin-film silicon solar cells are a potentially low-cost alternative to solar cells based on bulk silicon that are commonly used in the industry at the present time. However, a major drawback of the current epitaxial semi-industrial screen-printed cells is that they only achieve an efficiency of about 11-12%. By upgrading their efficiency, this kind of solar cell would become more attractive to the photovoltaic industry. The optimization of the front surface texture by dry texturing based on a fluorine plasma and the introduction of an intermediate porous silicon reflector at the epi/substrate interface (multiple Bragg reflector) has proven to result in an efficiency boost up to about 14%.